Difference between revisions of "Sprint Pre 2"
(→Step 1) |
m (→Step 16: update with 2.2.4 scripts) |
||
(12 intermediate revisions by 5 users not shown) | |||
Line 3: | Line 3: | ||
= Hardware = | = Hardware = | ||
− | Rich Dunbar has created a very detailed step by step pictorial guide for swapping a Sprint Pre- comms board into a Pre 2. | + | Rich Dunbar has created a very detailed step by step pictorial guide for swapping a Sprint Pre- comms board into a Pre 2. Important note that the Sprint Comm board must be activated PRIOR to this process. Cannot activate a Sprint Comm board through the Pre 2 at this time. You should also have already read through and understand the entire software portion (Step 16 in this guide) BEFORE starting this process. Pay special attention to Step 2: Prepare Your Palm Profile. |
− | == Step 1 == | + | |
+ | == Step 1 - Introduction == | ||
+ | <span id="Step_1"></span> | ||
[[Image:Slide1.PNG]] | [[Image:Slide1.PNG]] | ||
== Step 2 == | == Step 2 == | ||
+ | <span id="Step_2"></span> | ||
[[Image:Slide2.PNG]] | [[Image:Slide2.PNG]] | ||
== Step 3 == | == Step 3 == | ||
+ | <span id="Step_3"></span> | ||
[[Image:Slide3.PNG]] | [[Image:Slide3.PNG]] | ||
== Step 4 == | == Step 4 == | ||
+ | <span id="Step_4"></span> | ||
[[Image:Slide4.PNG]] | [[Image:Slide4.PNG]] | ||
== Step 5 == | == Step 5 == | ||
+ | <span id="Step_5"></span> | ||
[[Image:Slide5.PNG]] | [[Image:Slide5.PNG]] | ||
== Step 6 == | == Step 6 == | ||
+ | <span id="Step_6"></span> | ||
[[Image:Slide6.PNG]] | [[Image:Slide6.PNG]] | ||
== Step 7 == | == Step 7 == | ||
+ | <span id="Step_7"></span> | ||
[[Image:Slide7.PNG]] | [[Image:Slide7.PNG]] | ||
== Step 8 == | == Step 8 == | ||
+ | <span id="Step_8"></span> | ||
[[Image:Slide8.PNG]] | [[Image:Slide8.PNG]] | ||
== Step 9 == | == Step 9 == | ||
+ | <span id="Step_9"></span> | ||
[[Image:Slide9.PNG]] | [[Image:Slide9.PNG]] | ||
== Step 10 == | == Step 10 == | ||
+ | <span id="Step_10"></span> | ||
[[Image:Slide10.PNG]] | [[Image:Slide10.PNG]] | ||
== Step 11 == | == Step 11 == | ||
+ | <span id="Step_11"></span> | ||
[[Image:Slide11.PNG]] | [[Image:Slide11.PNG]] | ||
== Step 12 == | == Step 12 == | ||
+ | <span id="Step_12"></span> | ||
[[Image:Slide12.PNG]] | [[Image:Slide12.PNG]] | ||
== Step 13 == | == Step 13 == | ||
+ | <span id="Step_13"></span> | ||
[[Image:Slide13.PNG]] | [[Image:Slide13.PNG]] | ||
== Step 14 == | == Step 14 == | ||
+ | <span id="Step_14"></span> | ||
[[Image:Slide14.PNG]] | [[Image:Slide14.PNG]] | ||
+ | '''YOU HAVE TO BE EXTRA CAREFUL WITH THE VOLUME ROCKER RIBBON AS IT WILL BREAK IF NOT ALIGNED PROPERLY''' | ||
+ | |||
== Step 15 == | == Step 15 == | ||
+ | <span id="Step_15"></span> | ||
[[Image:Slide15.PNG]] | [[Image:Slide15.PNG]] | ||
= Software = | = Software = | ||
− | == Step | + | == Step 16 == |
− | + | <span id="Step_16"></span> | |
− | Follow the instructions on [[WebOS_2_Upgrade]] and use the ./scripts/meta-sprint-pre2-2. | + | Follow the instructions on [[WebOS_2_Upgrade]] and use the ./scripts/meta-sprint-franken-unlocked-pre2-2.2.4 or ./scripts/meta-sprint-franken-verizon-pre2-2.2.4 depending upon whether your Pre 2 is Unlocked or Verizon branded. See [http://www.webos-internals.org/wiki/WebOS_2_Upgrade#Sprint_Franken_Unlocked_Pre_2 Sprint_Franken_Unlocked_Pre_2] or [http://www.webos-internals.org/wiki/WebOS_2_Upgrade#Sprint_Franken_Verizon_Pre_2 Sprint_Franken_Verizon_Pre_2] |
Latest revision as of 23:33, 5 October 2017
This is the page where we document the complete Sprint Pre 2 procedure, hardware and software.
Hardware
Rich Dunbar has created a very detailed step by step pictorial guide for swapping a Sprint Pre- comms board into a Pre 2. Important note that the Sprint Comm board must be activated PRIOR to this process. Cannot activate a Sprint Comm board through the Pre 2 at this time. You should also have already read through and understand the entire software portion (Step 16 in this guide) BEFORE starting this process. Pay special attention to Step 2: Prepare Your Palm Profile.
Step 1 - Introduction
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Step 9
Step 10
Step 11
Step 12
Step 13
Step 14
YOU HAVE TO BE EXTRA CAREFUL WITH THE VOLUME ROCKER RIBBON AS IT WILL BREAK IF NOT ALIGNED PROPERLY
Step 15
Software
Step 16
Follow the instructions on WebOS_2_Upgrade and use the ./scripts/meta-sprint-franken-unlocked-pre2-2.2.4 or ./scripts/meta-sprint-franken-verizon-pre2-2.2.4 depending upon whether your Pre 2 is Unlocked or Verizon branded. See Sprint_Franken_Unlocked_Pre_2 or Sprint_Franken_Verizon_Pre_2