Angstrom on Touchpad
Booting Angstrom on the TouchPad is actually fairly easy. Here are the steps to get it going.
What to boot
For this we will have a beagleboard of Angstrom located in an LVM on the touchpad named ext2fs. This is un-tested with an ext3 filesystem, but it will likely work. The Angstrom rootfs needs to be right in the base of the LVM, not in a sub-folder.
We are going to be creating a multi-file uImage. It will be one file with both a uImage kernel as well as an initrd.
Gather required bits
First novaterm into the TouchPad and run the following commands
cd /var/home/root tar czvf boot.tgz -C /boot/ .
Then exit out of novaterm and back on your PC run the following
mkdir -p uImage/initrd cd uImage novacom get file:///var/home/root/boot.tgz > boot.tgz
This will have everything you need to create the multi-file uImage using whatever kernel is currently installed on your TouchPad. I would recommend using either UberKernel or F15... something that gives console output on bootup.
Build the initrd
First we need to make an empty file that will be used for our initrd. We will be starting off with an 8M initrd.
dd if=/dev/zero of=ramdisk bs=1M count=8 mke2fs -Fvm0 ramdisk mount -o loop ramdisk initrd
Now we have an empty initrd ramdisk file and it is mounted as a loopback so that we can put things into it.
Fill the initrd
This one is pretty simple. We are going to fill the initrd with the contents of the boot.tgz EXCEPT for the kernel.
mkdir boottemp tar xzvf boot.tgz -C boottemp rm boottemp/uImage mv boottemp/uImage-2.6.35-palm-tenderloin mv boottemp/* initrd
Change the pivot_root
You need to edit the file /sbin/init within the initrd to alter what rootfs is loaded at bootup
find these lines:
lvm.static lvchange -ay --ignorelockingfailure /dev/mapper/store-root # May need to say "don't update mtab" option below mount -o ro /dev/mapper/store-root /realroot
And change them to
lvm.static lvchange -ay --ignorelockingfailure /dev/mapper/store-ext2fs # May need to say "don't update mtab" option below mount -o ro /dev/mapper/store-ext2fs /realroot
And you are now done with creating the initrd. You can umount initrd now if you like, or leave it mounted if you are going to be making changes and testing them.
Build the multi-file uImage
You will need the package uboot-mkimage (at least on Ubuntu) installed to do this
I have worked up a script that runs the needed commands for you.
#!/bin/bash rm uMulti uRamdisk mkimage -A arm -O linux -T ramdisk -C none -d ramdisk uRamdisk mkimage -a 0 -e 0 -A arm -O linux -T multi -C none -d uImage-2.6.35-palm-tenderloin:uRamdisk uMulti
Just name the file something like spin-kernel.sh and give it execute permission. It should be inside of the uImage folder we made earlier, then give it a run.
One thing that I have found is that the checkroot script was not running early enough so it was halting the boot due to the rootfs still being read-only. To fix this go to /etc/rcS.d within your angstrom rootfs. Find the symlink that points to ../init.d/checkroot and rename it to S01checkroot
To do this, just put the Touchpad into recovery mode and memboot the multi-file uImage we made earlier. Because we are membooting it, if something go's wrong and the Touchpad doesn't boot properly, you can force a reboot by holding Home+Power for 10 seconds and it will safely reboot into webOS!